四、一般 P&I Clubs 承擔的責任為何（請列舉五項）？（20 分）

一、SURVEY REPORT OF CORRECTING THE DRAFT The surveyor has read six drafts-forward, aft and midships on both sides. These must be reduced to a single correct mean draft with which to enter the displacement tables. The reduction involves correcting for the effects of list, trim and hull deformation. If the ship was perfectly upright, on an even keel and not bent at all, then all six drafts would be the same. This draft would be the one to use. It never happens like that in practice. （20 分）

二、PRE-SHIPMENT SURVEYS Pre-shipment surveys are inspections of the cargo or the compartment where it will be stowed before loading. The intention of the survey will vary depending on who calls for it. Shipowners and their P&I clubs will call for pre-shipment surveys where they know that large cargo claims are likely to arise. The intention of the survey is then to make sure that the exact condition of the cargo on loading is specified on the bills of lading, and that due care has been taken in preparing the ship for the cargo. They can then more easily refute damage claims. Underwriters for the cargo may call for a warranty survey when high value cargo is to be shipped.（20 分）

三、HULL INSPECTION The surveyor should inspect all accessible parts of the hull and if he has any doubts about the sections he cannot reach, he should arrange for a ladder or a mechanical hoist so that these areas can be properly inspected. If the vessel is over ten years old, it may also be beneficial to do ultra sound thickness tests on portions of the deck to verify the plate thickness. Areas that should be inspected include: a. External and internal shell plating (where visible) b. Decks, deck houses, superstructures and bulwarks/rails c. Hatch coaming, hatches (including seals and securing devices) d. Hold ladders, gangways and catwalks e. Hold and deck lighting f. All pipes (above and below deck) g. Ventilators, manholes and watertight doors h. All holds/cargo tanks paying particular attention to beams and frames, bulkheads i. Tanktops j. Bilges and bilge suctions k. Double bottoms and peak tanks （20 分）

四、CARGO SURVEY Bulk cargoes must usually be sampled before loading. This may be for quality control, for ascertaining moisture content or for checking temperature. Sampling procedures tend to vary according to the practice of the port or terminal. Internationally accepted standards are laid down in British standards and in the IMO Code of Safe Practice for Solid Bulk Cargoes.（20 分）

五、海事公證人 海事公證人是一位實務的專業人員，他可能是一位技術人員、統計學家、數學家、 化學家、推銷員、商人、航海員、偵探、冷凍專家、石油專家、廣告商、拾荒者、 銀行家、製造商、造船商、租船人、文職人員。 （10 分）

六、貨櫃公證 貨櫃編號 WHLU-1234567 看起來是沒有任何明顯的損壞或異味，且內部清潔，櫃門 密封狀況良好，貨櫃屬於滿意狀態，足以承接冷藏貨品運送。該貨櫃未做預先冷卻。 （10 分）

一、依據「各類場所消防安全設備設置標準」規定，小規模老人服務機構之水系統滅火 設備設計原則為何？為能提升避難弱者生命安全保障，俾利在火災發生初期，採行 相關緊急滅火應變作為，減少傷亡風險發生，試比較我國與日本等先進國家對此類 場所在規範水系統滅火設備設計規定之差異處，並請說明有那些補強設計原則可讓 現場醫護人員（非工務勞安人員）確實有效操作該系統設備？（25 分）

二、水霧滅火設備可撲滅電器類火災之原理為何？水霧噴頭及配管與 190 電壓（KV）之 高壓電器設備應保持多少毫米（mm）之離開距離？請繪出水霧滅火設備主要設備與 系統配件構成之昇位圖。（25 分）

三、有一印刷機房之空間規模為 35 m（長）× 25 m（寬）× 12 m（高） ，內有一座印刷機 台大小為 12 m（長）× 8 m（寬）× 6 m（高） ，需設置固定式滅火設備來防護之，若 採用高發泡放出口之泡沫滅火設備及第一種膨脹比泡沫，泡沫原液（使用水成膜泡 沫滅火藥劑）濃度為 6%，且其防護區域開口部能在泡沫水溶液放射前自動關閉，請 問至少應設置幾個高發泡放出口？高發泡放出口之泡沫水溶液放射量為多少？充滿 配管之泡沫水溶液量為 0.8 立方公尺（m3），試計算其所需最小泡沫原液量？其泡沫 原液儲槽設置規定為何？（25 分）

⑴中繼幫浦設計之目的為何？（5 分）

114年 - 114 專技普考_海事保險公證人：海事查勘鑑定#127446

113年 - 113 專技普考_海事保險公證人：海事查勘鑑定#120243

112年 - 112 專技普考_海事保險公證人：海事查勘鑑定#114589

111年 - 111 專技普考_海事保險公證人：海事查勘鑑定#108363

110年 - 110 專技普考_海事保險公證人：海事查勘鑑定#101371

109年 - 109 專技普考_海事保險公證人：海事查勘鑑定#86665

108年 - 108 專技 海事查勘鑑定#76572

107年 - 107專技普考 - 海事查勘鑑定#69695

106年 - 106年專技普考-海事查勘鑑定#62895

105年 - 105年保險代理經紀公證人普通海事查勘鑑定#52554