阿摩線上測驗 登入

最新科目

最新試卷

115年 - 115-2 司法官特種考試_三等_司法官及律師、專技高考_律師_各類科:民法與民事訴訟法(二)#147090(5題)

115年 - 115-2 司法官特種考試_三等_司法官及律師、專技高考_律師_各類科:國文(作文)#147089(2題)

115年 - 115-2 司法官特種考試_三等_司法官及律師、專技高考_律師_律師(選試勞動社會法)、司法官及律師(選試勞動社會法):勞動社會法#147088(3題)

115年 - 115-2 司法官特種考試_三等_司法官及律師、專技高考_律師_各類科:憲法與行政法#147087(3題)

115年 - 115-2 司法官特種考試_三等_司法官及律師、專技高考_律師_律師(選試財稅法)、司法官及律師(選試財稅法):財稅法#147086(4題)

115年 - 115-2 司法官特種考試_三等_司法官及律師、專技高考_律師_律師(選試智慧財產法)、司法官及律師(選試智慧財產法):智慧財產法#147085(5題)

115年 - 115-2 司法官特種考試_三等_司法官及律師、專技高考_律師_律師(選試海商法與海洋法)、司法官及律師(選試海商法與海洋法):海商法與海洋法#147084(8題)

115年 - 115-2 司法官特種考試_三等_司法官及律師、專技高考_律師_各類科:刑法與刑事訴訟法#147083(4題)

115年 - 115-2 司法官特種考試_三等_司法官及律師、專技高考_律師_各類科:公司法、保險法與證券交易法#147082(4題)

115年 - 115-3 交通部航港局_航海人員測驗_一等管輪:輪機工程(包括推進裝置、輔機與輪機英文)#147081(40題)

最新試題

最新申論題

最新課程

最新主題筆記

最新討論

16 甲員警利用職務上之權力與機會,在取締性交易場所時,強制猥褻店內的應召女子,請問甲除了觸犯刑法 第 224 條強制猥褻罪外,還應另以何條論處? (A)刑法第 134 條之公務員加重處罰規定 (B)刑法第 121 條之職務行為受賄罪 (C)刑法第 122 條之違背職務受賄罪 (D)刑法第 131 條之圖利罪

29. Which of the following is identified in the passage as a primary cause of ethnic conflict? (A) Differences in thinking and mindset. (B) Competition over political power and resources. (C) Lack of interest in cultural roots. (D) Excessive migration between urban and rural areas.

30. According to the passage, why do historical memories often intensify ethnic tensions? (A) They encourage groups to forget past injustices. (B) They lay the foundations for reconciliation and cohesion. (C) They reinforce group identity and deepen divisions. (D) They eliminate the need for political representation.

31. Which one is true about the consequences of ethnic conflicts? (A) They are impenetrable barriers for different ethnic groups. (B) They may also pose a potential threat to neighboring states. (C) They will strengthen democracy, the solution to ethnic conflicts. (D) The displaced population will build inclusive governments.

46. 甜工加工件方法之敘述,下列何者『錯誤』?(A)手弓鋸每分鐘鋸削次數以50~60次為恰當 (B)鈍刀鈍削速率每分鐘約50~60次為恰當 (C)鈍刀用畢,要用鋼刷刷乾淨,不可上油 (D)一般手弓鋸鋸削行程,應佔鋸條全長的80%以上

47. 有關攻螺紋之敘述,下列何者『錯誤』?(A)攻牙過程中螺絲攻斷裂時,不可換另一支新的螺絲攻再繼續攻下去(B)每約銳1圈螺紋、退約 $1/4$ 圈,以便斷屑(C)於鑄鐵工件上攻、銳螺紋,可以不用潤滑油(D)一般攻製的螺紋約為實際標準的 $60\%$